|
05-29-2009, 01:36 PM
|
#1
|
Senior Member
Join Date: Jun 2008
Location: Wewahitchka, FL
Posts: 1,204
|
Hustler antenna shaft, "got the shaft"
When we pulled out of the last campground a few weeks ago it was windy and raining. We decided to pack it in and head home on the spur of the moment. Consequently, in such a rush and trying to keep dry, I forgot a couple of things. I took my old Hustler mount down, packed away the resonators and forgot the antenna shaft. I didn't discover I had left it for several days. I had that foldover shaft for 30 years or more.
After kicking myself for several days, I decided the only thing to do was order another. Rather than replace it with the same type foldover, I decided I would order a standard 54 inch straight shaft (Hustler MO3). It was cheaper too. I placed my order with Ham Radio Outlet (Atlanta) and in a few days received the below, damaged MO3. I had ordered a "straight shaft". I called HRO and they shipped a new one immediatly. I'm still waiting for UPS to pick up the damaged item. I was told if they didn't come within five days to get rid of the item. It doesn't look like they are coming. Anyone got any ideas on how to straighten this thing ? It's solid aluminum with a vinyle coating. Seems like a waste to just toss it.
I have to say HRO is a good place to do business or always has been for me. They didn't question my claim and were willing to ship to a campground if I had been on the road. I might add this disclaimer: I have no financial interest in Ham Radio Outlet. I just thinik it's a great place to do business.
__________________
Jim ~ W4EWA
|
|
|
05-30-2009, 06:01 PM
|
#2
|
Junior Member
Join Date: Nov 2007
Posts: 1
|
maybe you could put one end in a vice , put a tight fiting pipe on the other end and be very gentle bend it on the bend. it might work.
|
|
|
05-30-2009, 09:49 PM
|
#3
|
Senior Member
Join Date: Jun 2008
Location: Gateway to the thumb
Posts: 243
|
Quote:
Originally Posted by One Country Boy
When we pulled out of the last campground a few weeks ago it was windy and raining. We decided to pack it in and head home on the spur of the moment. Consequently, in such a rush and trying to keep dry, I forgot a couple of things. I took my old Hustler mount down, packed away the resonators and forgot the antenna shaft. I didn't discover I had left it for several days. I had that foldover shaft for 30 years or more.
After kicking myself for several days, I decided the only thing to do was order another. Rather than replace it with the same type foldover, I decided I would order a standard 54 inch straight shaft (Hustler MO3). It was cheaper too. I placed my order with Ham Radio Outlet (Atlanta) and in a few days received the below, damaged MO3. I had ordered a "straight shaft". I called HRO and they shipped a new one immediatly. I'm still waiting for UPS to pick up the damaged item. I was told if they didn't come within five days to get rid of the item. It doesn't look like they are coming. Anyone got any ideas on how to straighten this thing ? It's solid aluminum with a vinyle coating. Seems like a waste to just toss it.
I have to say HRO is a good place to do business or always has been for me. They didn't question my claim and were willing to ship to a campground if I had been on the road. I might add this disclaimer: I have no financial interest in Ham Radio Outlet. I just thinik it's a great place to do business.
|
The only radio I bought new was my V-8 HT, and I got it from HRO.
__________________
Dan,
Almost a Marine (Army/Navy)
15 months in VietNam (12 Army/3 Navy)
Love to
|
|
|
05-31-2009, 05:54 PM
|
#4
|
Senior Member
Join Date: Nov 2007
Location: Mobile, on the road
Posts: 1,139
|
I have dealt with HRO on a couple of occasions.
And I can say I'm 100% pleased with them
I've also purchased from AES... And likwise am happy, got to call them again though when I have a couple of bucks to spare (I'm serious, $2.00 should cover it)
|
|
|
06-04-2009, 08:14 AM
|
#5
|
Member
Join Date: May 2008
Location: Miami, FL / Ashburn, VA
Posts: 90
|
Jim: You might try heating it up with a heat gun combined with a vise. I have never had the situation but thats what my brain can come up with..73
__________________
Mark Johnson - W3ZI
2007 National Sea Breeze LX / 8367
2007 Chevrolet Malibu Toad
TS2000 / Yaesu 857D and a Tarheel Antenna
|
|
|
06-04-2009, 05:40 PM
|
#6
|
Senior Member
Join Date: Nov 2007
Location: Southwest, Illinois
Posts: 311
|
I have dealt with HRO, too, and was very pleased.
__________________
Jeff WØJPS
1977 Diamond Class C
(Ford E350, 460)
|
|
|
06-08-2009, 10:15 AM
|
#7
|
Member
Join Date: Dec 2007
Location: Cut & Shoot, TX
Posts: 98
|
Bent Shaft
If you put heat on it, be carefull not to over heat it, aluminum has a low melting point. If you can get access to the inside of the tube, pack it full with sand to prevent any crimping when bending.
If it is crimped badly, just cut it in two pieces and solder a sleeve on it. If you can't find an aluminum sleeve to fit, try copper. The plumbing section of your hardware store should have something close.
Good luck on fixing it. Let us know how it worked out,
__________________
Dizzy Dick (WB3DZY)
Newmar Dutch Star
Jeep Liberty 4x4 Toad
|
|
|
06-09-2009, 06:26 PM
|
#8
|
Senior Member
Join Date: Jun 2008
Location: Wewahitchka, FL
Posts: 1,204
|
I haven't tackled the shaft yet. Thanks for the ideas. It has a vinyle or plastic coating around the aluminum, so if I apply heat, I would probably just removed the coating. I may look around for a machine shop and see if they have a way to straighten it. It's not crimped at all, just a gradual bend. Will let you know how it works out. Thanks for all the ideas guys, I 'preciate it.
Jim
__________________
Jim ~ W4EWA
|
|
|
06-10-2009, 09:12 AM
|
#9
|
Senior Member
Join Date: Nov 2007
Location: Mobile, on the road
Posts: 1,139
|
There is a very easy way to straighten it if it's not crimped.. I don't think a muffler shop (Custom muffler shops bend pipe all the time) will have dies that small (in fact I know they won't) but a plumber might. And that's all it takes.
If the shaft, normally, is straight, not tapered, and if the end cap can be removed or if the end cap is the same outside diameter as the shaft you can slip a spring of the same ID as the shaft is OD over it, this prevents crimping on gentle bends.
That's also how the die method works
|
|
|
06-10-2009, 09:13 AM
|
#10
|
Senior Member
Join Date: Nov 2007
Location: Mobile, on the road
Posts: 1,139
|
Duplicate due to software error
|
|
|
07-07-2009, 10:59 PM
|
#11
|
Senior Member
Join Date: Jun 2008
Location: Wewahitchka, FL
Posts: 1,204
|
Hi Guys,
I'll take a photo of the shaft in a day or two and post it. I've got it almost straight. I've just been working with it very gingerly on a cushioned stool. So-far, so-good.... It is usable now and if you didn't look closely you probably would not even know it was not perfect.
Thank you for all the suggestions. I just decided I was going to attempt it this way and it's been working.
~ Jim ~
__________________
Jim ~ W4EWA
|
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|